Stewart
Guru
- Joined
- Sep 16, 2009
- Messages
- 603
- Reaction score
- 6
It's been a while since I've installed the Sangoma UT50 from scratch so I'm re-following the directions here.
It's a new Silver build. Status is:
┌────────────────────────System Information───────────────────────────┐
│ Asterisk = ONLINE | Dahdi = ONLINE | MySQL = ONLINE │
│ SSH = ONLINE | Apache = ONLINE | Iptables = ONLINE │
│ Fail2ban = ONLINE | Internet = ONLINE | Ip6Tables = OFFLINE │
│ BlueTooth = OFFLINE | Hidd = OFFLINE | NTPD = ONLINE │
│ SendMail = ONLINE | Samba = OFFLINE | Webmin = ONLINE │
│ Ethernet0 = ONLINE | Ethernet1 = N/A | Wlan0 = N/A │
│ │
│ PBX in a Flash Version = 1.7.5.7 Running on *HARDWARE* │
│ FreePBX Version = 2.8.1.4 │
│ Running Asterisk Version = 1.4.42 │
│ Asterisk Source Version = 1.4.42 │
│ Dahdi Source Version = 2.5.0.2+2.5.0.2 │
│ Libpri Source Version = 1.4.12 │
│ Addons Source Version = 1.4.13 │
│ IP Address = 192.168.0.165 on eth0 │
│ Operating System = CentOS release 5.7 (Final) │
│ Kernel Version = 2.6.18-274.3.1.el5 - 32 Bit
It's a new Silver build. Status is:
┌────────────────────────System Information───────────────────────────┐
│ Asterisk = ONLINE | Dahdi = ONLINE | MySQL = ONLINE │
│ SSH = ONLINE | Apache = ONLINE | Iptables = ONLINE │
│ Fail2ban = ONLINE | Internet = ONLINE | Ip6Tables = OFFLINE │
│ BlueTooth = OFFLINE | Hidd = OFFLINE | NTPD = ONLINE │
│ SendMail = ONLINE | Samba = OFFLINE | Webmin = ONLINE │
│ Ethernet0 = ONLINE | Ethernet1 = N/A | Wlan0 = N/A │
│ │
│ PBX in a Flash Version = 1.7.5.7 Running on *HARDWARE* │
│ FreePBX Version = 2.8.1.4 │
│ Running Asterisk Version = 1.4.42 │
│ Asterisk Source Version = 1.4.42 │
│ Dahdi Source Version = 2.5.0.2+2.5.0.2 │
│ Libpri Source Version = 1.4.12 │
│ Addons Source Version = 1.4.13 │
│ IP Address = 192.168.0.165 on eth0 │
│ Operating System = CentOS release 5.7 (Final) │
│ Kernel Version = 2.6.18-274.3.1.el5 - 32 Bit
- Insert the USB Wanpipe VoiceTime Device into the Server USB Port DONE
- - Make sure dahdi has already been installed on your system
* The following step assumes that you do not have dahdi on your system. If you already have dahdi installed with accompanying sources AND can verify working /etc/init.d/dahdi scripts, then skip to STEP 4
Go to the following website to download Zaptel:
-> http://downloads.asterisk.org/pub/telephony/dahdi-linux/releases/
Should be done since the status shows it and the script exists. - Untar and install dahdi:
-> cd /usr/src
-> tar xfz dahdi-<ver>.tgz
-> cd dahdi-<ver>
-> make
-> make install
-> make config
Shouldn't need to do it since it's already installed. - Download the Wanpipe Voicetime Driver
DONE - Untar and change directory
-> tar xfz wanpipe-voicetime-<ver>.tgz
-> cd wanpipe-voicetime-<ver>
DONE - Build Wanpipe VoiceTime for Currently Running Zaptel Module
-> make DAHDI_DIR=/usr/src/dahdi-<ver>/linux
DAHDI_DIR= location of dahdi source used to build and install dahdi
By default DAHDI_DIR=/usr/src/zaptel
I can't seem to find the dahdi source. I don't see a /usr/src/zaptel or a /usr/src/dahdi-2.5.0.2/linux or similar. I do see /usr/src/dahdi/linux. Is that it? - Install VoiceTime module
-> make install
- - Install bootup startup script for VoiceTime
-> make boot
The wanpipe_voicetime uses /etc/init.d/dahdi script. The dahdi startup script must be installed
eg: cd /usr/src/dahdi-<version>
make #build dahdi
make install #install dahdi modules
make config #install dahdi boot script
- - Start Wanpipe VoiceTime using dahdi Startup Script
-> /etc/init.d/dahdi start - Confirm that VoiceTime Sync Tool is working
-> Click Here