On May 27, 2013, I downloaded the pbxinaflash20643-i386.iso and during setup I get a warning I'm using the 2.0.6.4.1 ISO and that it's not supported. ISO is called pbxinaflash20643-i386.iso
but continued with the install on one of my sandboxes (machine A) regardless and all seems to be fine... still in 'playing' mode, I have yet to test most of it out...
Now... I thought I would install this on another sandbox (machine B) (Intel P4 with 2GB RAM 80GB Hard drive) which is running:
PBX in a Flash PURPLE Status Program
──────────────────────────────────────────────────────────────────────────────
┌────────────────────────SYSTEM INFORMATION───────────────────────────┐
│ Asterisk = ONLINE | Dahdi = ONLINE | MySQL = ONLINE │
│ SSH = ONLINE | Apache = ONLINE | Iptables = ONLINE │
│ Fail2ban = ONLINE | Internet = ONLINE | Ip6Tables = ONLINE │
│ Disk Free = ADEQUATE| Mem Free = ADEQUATE| NTPD = ONLINE │
│ SendMail = ONLINE | Samba = OFFLINE | Webmin = ONLINE │
│ Ethernet0 = ONLINE | Ethernet1 = N/A | Wlan0 = N/A │
││
│ PIAF Installed Version = 2.0.6.2 under *HARDWARE* │
│ FreePBX Version = 2.9.0.12 │
│ Running Asterisk Version = 1.8.8.0 │
│ Asterisk Source Version = 1.8.8.0 │
│ Dahdi Source Version = 2.5.0.2 │
│ Libpri Source Version = 1.4.12 │
│ IP Address = 192.168.0.102 on eth0 │
│ Operating System = CentOS release 6.2 (Final) │
│ Kernel Version = 2.6.32-220.7.1.el6.i686 - 32 Bit │
│ Incredible PBX 3 Version = 3.0.7 │
└─────────────────────────────────────────────────────────────────────┘
But when I boot from the install ISO, I get:
"Not enough RAM to install Centos OS" and the install process ends
Machine B is a better spec machine than Machine A, yet machine A wizzed right through and machine B does not get as far at all!
Any ideas please?
Thank you in advance!
but continued with the install on one of my sandboxes (machine A) regardless and all seems to be fine... still in 'playing' mode, I have yet to test most of it out...
Now... I thought I would install this on another sandbox (machine B) (Intel P4 with 2GB RAM 80GB Hard drive) which is running:
PBX in a Flash PURPLE Status Program
──────────────────────────────────────────────────────────────────────────────
┌────────────────────────SYSTEM INFORMATION───────────────────────────┐
│ Asterisk = ONLINE | Dahdi = ONLINE | MySQL = ONLINE │
│ SSH = ONLINE | Apache = ONLINE | Iptables = ONLINE │
│ Fail2ban = ONLINE | Internet = ONLINE | Ip6Tables = ONLINE │
│ Disk Free = ADEQUATE| Mem Free = ADEQUATE| NTPD = ONLINE │
│ SendMail = ONLINE | Samba = OFFLINE | Webmin = ONLINE │
│ Ethernet0 = ONLINE | Ethernet1 = N/A | Wlan0 = N/A │
││
│ PIAF Installed Version = 2.0.6.2 under *HARDWARE* │
│ FreePBX Version = 2.9.0.12 │
│ Running Asterisk Version = 1.8.8.0 │
│ Asterisk Source Version = 1.8.8.0 │
│ Dahdi Source Version = 2.5.0.2 │
│ Libpri Source Version = 1.4.12 │
│ IP Address = 192.168.0.102 on eth0 │
│ Operating System = CentOS release 6.2 (Final) │
│ Kernel Version = 2.6.32-220.7.1.el6.i686 - 32 Bit │
│ Incredible PBX 3 Version = 3.0.7 │
└─────────────────────────────────────────────────────────────────────┘
But when I boot from the install ISO, I get:
"Not enough RAM to install Centos OS" and the install process ends
Machine B is a better spec machine than Machine A, yet machine A wizzed right through and machine B does not get as far at all!
Any ideas please?
Thank you in advance!