TIPS GVSIP Issue on RasPi

RSDunn

New Member
Joined
Aug 4, 2013
Messages
11
Reaction score
1
Stupid Question: Does GV work for incoming and outgoing call without the caller id? thanks!
Yes I do have incoming and outgoing calls working w GVSIP ... just no callerID going out to the end points when dialing through GVSIP trunk
 

weenus500

Member
Joined
Dec 28, 2014
Messages
38
Reaction score
1
Yes I do have incoming and outgoing calls working w GVSIP ... just no callerID going out to the end points when dialing through GVSIP trunk
thanks for the reply. I have been doing this with a pi2. I want to stick the card in a p3 I have available and see if I have any better luck.
 

weenus500

Member
Joined
Dec 28, 2014
Messages
38
Reaction score
1
incrediblepbx13-raspbian8-gvsip.zip 2018-07-21 1.4 GB -- I found this updated version of the installer which i am very excited about trying. The set up was super smooth. I got everything done at work up to the point where one sets up the google trunk.
I hope I am permitted this one question.
Can the freepbx gui be used to set up the GV trunk with the outgoing and incoming routes?
 

RSDunn

New Member
Joined
Aug 4, 2013
Messages
11
Reaction score
1
incrediblepbx13-raspbian8-gvsip.zip 2018-07-21 1.4 GB -- I found this updated version of the installer which i am very excited about trying. The set up was super smooth. I got everything done at work up to the point where one sets up the google trunk.
I hope I am permitted this one question.
Can the freepbx gui be used to set up the GV trunk with the outgoing and incoming routes?
The gvsip trunk isn't able to be setup via the GUI. use this link to get the tar file and installer to build it for you...
http://nerdvittles.com/?p=26315

If you get callerID working please post!
 

weenus500

Member
Joined
Dec 28, 2014
Messages
38
Reaction score
1
The gvsip trunk isn't able to be setup via the GUI. use this link to get the tar file and installer to build it for you...
http://nerdvittles.com/?p=26315

If you get callerID working please post!
I was able to get it working finally. To make the callerID work, I just put "My Name"<2014316165> in the outbound callerID.
The gvsip trunk isn't able to be setup via the GUI. use this link to get the tar file and installer to build it for you...
http://nerdvittles.com/?p=26315

If you get callerID working please post!
After getting it working, I was able to get callerID to show up by inserting "my name"<8885551212> in Outbound Routes -> Route CID
 
Joined
Jun 18, 2013
Messages
34
Reaction score
4
I am running Asterisk 13.22.0 with GVSIP-NAF support and FreePBX 13 on Raspberry Pi 2+
After a fresh install I have four issues with my system:
1. GVSIP trunks give me intermittent no receive audio on outgoing calls. The call connects and the other party can hear me, but I cannot hear them.
2. Outgoing calls using GVSIP trunks do not provide ringback tone. There is silence until the other party answers.
3. HylaFax works fine for incoming faxes, but will not work for outgoing faxes. Always get messages like: "requeued Busy signal detected". The dialed number or numbers are not busy.
4. I've set one of my GVSIP trunks with an inbound route to extension 53669 (Lenny) but the inbound call with not complete. There is a long silence, the a beep, then disconnect. Extension 53669 works with internal calls.
Update on 8-1-2018: Did a complete new install again. Only problems #2 and #4 remain. Will try to troubleshoot via the log to figure out what is going one.
 
Last edited:

weenus500

Member
Joined
Dec 28, 2014
Messages
38
Reaction score
1
All of sudden I noticed pjsip is being rejected by google voice. I have a few google voice numbers and two raspis running freepbx and I noticed on the other one, they were still connecting so I deleted the trunk off the one where the trunks were all being rejected and added it to the one and then all those trunks started being rejected.
I did the fix a few weeks ago where you change line in pjsip_custom.conf from obihai.telephony.goog to voice..telephony.goog and that fixed things until this happened yesterday.
I think I'm screwed indefinitely now.
gvsip1/sip:eek:bihai.sip.google.com gvsip1 Rejected
gvsip2/sip:eek:bihai.sip.google.com gvsip2 Rejected
Any help?
 

wardmundy

Nerd Uno
Joined
Oct 12, 2007
Messages
15,221
Reaction score
2,662
Latest fix for all Incredible PBX platforms:
Code:
cp /etc/asterisk/pjsip_custom.conf /etc/asterisk/pjsip_custom.conf.old
sed -i 's|voice.telephony.goog|64.9.242.172|g' /etc/asterisk/pjsip_custom.conf
sed -i 's|voice.telephony.goog|64.9.242.172|g' /root/gvsip-naf/install-gvsip
amportal restart
 
  • Like
Reactions: weenus500

weenus500

Member
Joined
Dec 28, 2014
Messages
38
Reaction score
1
This morning the above fix stopped working. Strangely, I tried nmap -p 5061 64.9.242.172 and it sez "5061/tcp open sip-tls" I need some help again.
 

Members online

PIAF 5 - Powered by 3CX

Forum statistics

Threads
22,441
Messages
137,941
Members
14,611
Latest member
rampageai