TIPS BAD VALUE CALLER ID

[goblin]

System summary;

PIAF Installed Version = 2.0.6.4 under *HARDWARE*
FreePBX Version = 2.8.1.4
Running Asterisk Version = 1.8.22.0
Asterisk Source Version = 1.8.22.0
Dahdi Source Version = 2.6.2
Libpri Source Version = 1.4.12
IP Address = 192.168.14.53 on eth0
Operating System = CentOS release 6.4 (Final) <>
Kernel Version = 2.6.32-358.2.1.el6.i686 - 32 Bit

I have a private SIP trunk where i need to send the 10 Digit phone number so my carrier can "authenticate" and be able to placede the call.

At this moment im sending "bad value" as a caller ID but on my freepbx administration is setup to send the 10 digit phone number.

http://cl.ly/image/3j1F3B1A0P0a

ANY IDEAS GUYS????


Executing [s@macro-outbound-callerid:6] Set("SIP/5000-00000603", "USEROUTCID=<bad value>") in new stack
-- Executing [s@macro-outbound-callerid:7] Set("SIP/5000-00000603", "EMERGENCYCID=") in new stack
-- Executing [s@macro-outbound-callerid:8] Set("SIP/5000-00000603", "TRUNKOUTCID=6646220013") in new stack
-- Executing [s@macro-outbound-callerid:9] GotoIf("SIP/5000-00000603", "1?trunkcid") in new stack
-- Goto (macro-outbound-callerid,s,12)
-- Executing [s@macro-outbound-callerid:12] ExecIf("SIP/5000-00000603", "1?Set(CALLERID(all)=6646220013)") in new stack
-- Executing [s@macro-outbound-callerid:13] ExecIf("SIP/5000-00000603", "1?Set(CALLERID(all)=<bad value>)") in new stack
-- Executing [s@macro-outbound-callerid:14] ExecIf("SIP/5000-00000603", "0?Set(CALLERID(all)=)") in new stack

 

[krakastan]

but on my freepbx administration is setup to send the 10 digit phone number

how exactly is it setup?

 

[goblin]

Here is the trunk setup.

http://cl.ly/image/3F322z013b2x

 

[Jeff Schade]

Try setting CID on your outbound routes page rather than in the trunk.

 

[goblin]

i have already did it and i have the same issue.. i Dont know if on a lower level i can overwrite this any ideas?? or any other wey to overwrite globally the CID?

 

[goblin]

I already did that and go the same issue, any other ideas how can i overwrite globally the CID, may be on config file??

 

[Jeff Schade]

Who is your carrier? Did you contact them about what they expect the CID value to be?

 

[goblin]

yes, they expect 6646220013 to authenticate, the call against the proxy, but they seeing " Bad Value" instead if the number. Check this log i send the number next is the "bad value" message.

Executing [s@macro-outbound-callerid:6] Set("SIP/5000-00000603", "USEROUTCID=<bad value>") in new stack
-- Executing [s@macro-outbound-callerid:7] Set("SIP/5000-00000603", "EMERGENCYCID=") in new stack
-- Executing [s@macro-outbound-callerid:8] Set("SIP/5000-00000603", "TRUNKOUTCID=6646220013") in new stack
-- Executing [s@macro-outbound-callerid:9] GotoIf("SIP/5000-00000603", "1?trunkcid") in new stack
-- Goto (macro-outbound-callerid,s,12)
-- Executing [s@macro-outbound-callerid:12] ExecIf("SIP/5000-00000603", "1?Set(CALLERID(all)=6646220013)") in new stack
-- Executing [s@macro-outbound-callerid:13] ExecIf("SIP/5000-00000603", "1?Set(CALLERID(all)=<bad value>)") in new stack
-- Executing [s@macro-outbound-callerid:14] ExecIf("SIP/5000-00000603", "0?Set(CALLERID(all)=)") in new stack​

 

[goblin]

im also getting this on /var/log/asterisk/full

[2013-06-11 15:14:45] WARNING[1847] chan_sip.c: Received response: "Forbidden" from '"badvalue" <sip:[email protected]>;tag=as4e9476e4'

 

[Jeff Schade]

Why are you setting the caller ID in the PEER Details settings? FreePBX/PiaF sets that value in the "Route Settings"

 

[goblin]

i tried in both places, SIP Trunk settings and Outbound Routes. and is the same thing...

 

[randy7376]

If you haven't already, you can try fromuser=<10-digit-number> in your Trunks -> Outgoing Setings - Peer Details.

 

[goblin]

Thanks Randy, this resolved my issue. the important part is that outbound calls are working. But i still have the bad value thing.. i will Digg in to see what is happening..

 

[jeffmac]

I have no experience with your issues (Remember - experience is what you get when you don't get what you expected. ie: problem solving!) but doesn't "sendrpid=" and or "trustrpid=" have a bearing on whether the callerid is sent?

Jeff