Search results

OK... This is a genuine "Emily Latella" Moment" (RIP Gilda Radner)... I just forwarded UDP ports 10000-20000 and audio problems are gone. "OH!, Never mind..." Thanks, Don

Well... I am having the exact issue. I can call in and out, but there is absolutely no audio either direction. Port 5060 is forwarded to the server. I have not forwarded or opened ports 10000-20000. The server is behind a router and the router's WAN address is configured in the general sip...

:confused5: Well -- I spoke too soon. The remote vpn client is connected and the remote extension is registered but is again "unreachable", even with NAT=yes. It worked GREAT yesterday. Would a STUN server help resolve this? Anyone else using remote extensions via an openvpn tunnel? Any...

Hi Atsak, Thanks for responding. Actually I was doing something (very stupid) but I'll share my mistake. I had tried this several times and it never worked so I undid what I had been doing... I read that NAT might be the issue since the remote softphone was clearly behind several different...

Hello and thanks for reading my (long winded) post. I've searched the related postings but didn't quite find what I was looking for so here goes... I have had an Incredible PBX running extremely well on a pogoplug for over a year now. Recently I added an OpenVPN server running on a...

I didn't have much luck getting roadrunner to work. However, I followed these instructions to utilize my (almost-never used) gmail account to act as the relay host. Works great! http://www.gnali.org/?p=123

First -- Wow and Thanks to Ward and the whole group! I just built an Incredible PBX on the Pogoplug 4. I had my doubts but it works great!!! Very impressive! While Incredible PBX seems to work well on the Pogoplug 4 except for the Asteridex "Click-to-Dial" . Asteridex works great when...

Hello, Moving my phones to a Gotcha-Free RPi2 setup... With the old Incredible PBX, I could dial *80 +extension #, and that extension would ring once, auto-answer and go into a two-way intercom mode. I am no longer able to do this with the Gotch-Free setup. I've created several page groups...

Hello, On previous version of Incredible PBX, If another extension was ringing I could pick up that call from another non-ringing extension by pressing the flashing BLF button corresponding to the ringing extension. This feature seems to not work on the Gotcha-Free Raspberry Pi 2? I have...

Hi Kevin, From the command line interface (CLI, Terminal, etc.) type in: asterisk -vvvr If you need a more verbose output, issue the "asterisk" command with more "v"s. The more "v"s you enter the more "verbose" the output is. Then do Control-C to exit from it. My experience with the...

Over the past several days I've noticed that the available free RAM has been decreasing steadily. Here is a screenshot after running the server for about a week and the RAM is down to 35MB. However, I remembered the RAM being closer to 700 MB after the initial startup, etc. I then did an...

I've been experimenting.... Here is a new twist.... Asteridex works fine for SOME numbers in the same area code but not others. I have my daughter's cell phone entry in Asteridex. It is 937654XXXX and it works fine with Asteridex (a snippet of the CLI is below). However, Asteridex does...

Hi Ward, I've been experimenting with the Gotcha-Free for the Pi 2. This is probably the 5th or 6th time I've gone through the motions. But each time the results have been the same -- Asteridex fails on non-800 numbers. On the "default" configuration of the Gotcha-Free for Pi 2, Asteridex...

Hi Ward, I put the cli info in reply #8 (above), then in reply #9 explained about the single Vitelity trunk query. The first part of reply #8 shows the call going through and ringing when directly dialed. Then the same number when attempting to use Asteridex. I've separated these two...

Thanks Ward, Synack, Andy, etc. Not sure this is related, but I contacted Vitelity Tech Support about the failing calls. They indicate that two trunks are customarily used -- an inbound and an outbound trunk. That is how the previous Increcible PBXs worked. However, with the new Gotcha-Free...

Directly dialing “China Wok”.... Connected to Asterisk 11.16.0 currently running on incrediblepi2 (pid = 19592) == Using SIP RTP CoS mark 5 == Extension Changed 6001[default] new state InUse for Notify User 6004 -- Executing [9373200XXX@DLPN_DialPlanMain:1] Macro("SIP/6001-0000005a"...

Hi Ithown. Lenny appears to be working fine right out the box on my Gotcha-Free Raspberry Pi 2 pbx. I have not tried this yet, but I'm sure I could transfer a caller to Lenny (extension 53669). Hes a real hoot! Just waiting for Larissa to make it through Grad School!

I'm having "odd" issues with Vitelity with the Gotcha-Free on the Raspberry Pi model 2. In previous PBX configurations on "real" PCs, there generally were two trunks associated with Vitelity: An outbound trunk and an inbound trunk. The Gotcha-Free implementation on Raspberry Pi model 2 only...

No -- Vitelity appears to just use 10 digit format NXXNXXXXXX. I have my entries setup in Asteridex in this 10-digit form. The numbers stored there fail when using Asteridex but work fine when dialed directly. I've tried loading "1" or not load "1" per the instructions, as well as stripping...

Synack, Thanks for the response. This is "new" build using the same Raspberry Pi Model 2 hardware. This is the contents of the /etc/hosts file: 127.0.0.1 localhost ::1 pbx.local localhost ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1...