Search results

I have done that too, ssh to server, then run asterisk -rvvvvvvvvvvvv from the command line. What should I be looking for in the log?

Local. Is there a firewall log I can check?

I keep having an issue with outbound calling stops working. I did a tcpdump on my PBX to check if the call was leaving my server. I did not see any outbound traffic going to vitelity. Where would I look to correct this problem? I have checked the outbound trunk ( I only have one outbound trunk...

When I try to make an outbound call I get an error "All circuits are busy please try your call later" message. I only have one outbound route, sometimes it works, but the first thing in the morning when I try to make a call I get that error message. here is my call log, I did asterisk...

yea it's fixed now.. == Using SIP RTP TOS bits 184 == Using SIP RTP TOS bits 184 == Using SIP RTP CoS mark 5 == Using SIP RTP CoS mark 5 > 0x13c7730 -- Strict RTP learning after remote address set to: 64.2.142.13:14128 > 0x13c7730 -- Strict RTP learning after remote address...

I am working with vitelity support. They asked me a question that I don't know how to answer. -------- Vitelity support ------------------ To clarify, are you wanting your DIDs to route to your registered sub account, registering from IP 64.233.xx.xx, or do you want them to route directly to...

I ssh'd into the PBX and ran the command asterisk -rvvvvvvvvvv I then dialed one of my DID's and this is what was displayed. is this the correct log to look at? Using SIP RTP TOS bits 184 == Using SIP RTP TOS bits 184 == Using SIP RTP CoS mark 5 == Using SIP RTP CoS mark 5 >...

I just upgraded to IPBX 2020. On my old PBX I had one inbound trunk and I was able to direct my DID's to separate inbound destinations. I get my sip trunks from Vitelity I have two DID's that I have a inbound route for each DID. I would like to have a unique inbound route for each DID. I have...

I found the problem. I was trying to use the wrong UDP port. The phones were set to UDP 5061. I changed to 5060 and now it works.

The server is sitting behind a Firewall / NAT. Yes the original IP address is being used and I did update the new PBX to the old IP address. I tried to run the command service iptables stop, but it didn't do anything. The output is "Redirecting to /bin/systemctl stop iptables.service" but if I...

I setup my new PBX ( Incredible PBX 2020.1 for Centos 7, Asterisk 16.9.0, Incredible GUI 15.0.9.81) while the old one was still on line. I finally figured out how to change the IP address of the new PBX and I took the old PBX offline. After chasing the IP address of the new PBX, I rebooted. I...

Ok I think I have finally resolved most of my issues. I changed the Trunk that I have setup for Vitality and now I can make outbound calls. I have a ticket open with vitality because my inbound calls are ringing fast busy.

I am also having a problem with outbound calls. It was working then I deleted the default outbound route. I create a new outbound route but I keep getting "All circuits are busy, Please try again later". The asterisk console shows chan_sip.c:24400 handle_response_invite: received response...

I checked the file and it was already there.. the line in rc.local reads /usr/sbin/fwconsole restart I tried remove /usr/sbin from the line. Rebooted the computer and it still is coming up "Can Not Connect to Asterisk" However I can login as root and manually start asterisk from the command...

I recently installed IncrediblePBX 2020 and I am having problems. When I select the Dashboard tab, I see a big red sign at the top right "Can not connect to Asterisk". Rebooting the computer does not resolve the issue. Also I have deleted all the pre-configured trunks and added a Inbound and...

@Andrew your correct I did fix the issue. I apologize for not making that clear. Thanks for checking. Gotel

I was having a problem connecting to my home network using VPN because it was a common IP address range (192.168.1.x). So I changed the IP address range to 192.168.17.x Since I have changed the IP address to the new scheme, I am getting one way audio on my phones. I have checked all devices ip...

I just installed IPBX 13-13.3 for Scientific Linux, Asterisk 13.21.0 Incredible 13.0.120.10 ... The after install directions say to run /root/update-passwords. I don't have this file in my root directory. What username and password should I use to login the first time after install? Thanks, Gotel

Ward, whats the catch? Free isn't always free...

I checked with ting support, they stated the credits won't show up until Friday. I will check back if I don't see them. Thanks, Gotel