Hi
I am trying to connect asterisk with a Cisco GW 2600 with E1 pri using a Digium, Inc. Wildcard TE210P dual-span T1/E1/J1 card 3.3V (rev 02),
Errors:
[Jan 28 17:32:33] VERBOSE[6182] logger.c: == Primary D-Channel on span 1 up
[Jan 28 17:32:33] WARNING[6182] chan_dahdi.c: PRI Error on span 0: We think we're the CPE, but they think they're the CPE too.
[Jan 28 17:32:34] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:32:35] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:32:36] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:32:37] VERBOSE[6182] logger.c: == Primary D-Channel on span 1 down
[Jan 28 17:32:37] WARNING[6182] chan_dahdi.c: No D-channels available! Using Primary channel 16 as D-channel anyway!
[Jan 28 17:32:42] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1
[Jan 28 17:32:43] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:32:44] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:32:45] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:32:51] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
please someone help me,
rafael
Configuration details:
Cisco cisco 2650XM (Version 12.2(15)T14)
--------------------------------------------
!
isdn switch-type primary-net5
!
!
voice call send-alert
voice call convert-discpi-to-prog
voice call carrier capacity active
voice rtp send-recv
!
voice service voip
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback none
h323
!
!
controller E1 1/0
framing NO-CRC4
pri-group timeslots 1-31
!
!
!
interface FastEthernet0/0
ip address 192.168.12.210 255.255.255.0
ip route-cache same-interface
no ip route-cache
no ip mroute-cache
load-interval 30
speed 100
full-duplex
!
interface Serial1/0:15
no ip address
no logging event link-status
isdn switch-type primary-net5
isdn incoming-voice data
isdn bchan-number-order ascending
no cdp enable
!
ip http server
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.12.100
!
!
call rsvp-sync
!
voice-port 1/0:15
echo-cancel coverage 32
playout-delay nominal 150
playout-delay minimum low
cptone PE
bearer-cap 3100Hz
!
!
dial-peer voice 10 pots
destination-pattern .T
no digit-strip
direct-inward-dial
port 1/0:15
forward-digits all
!
gateway
timer receive-rtcp 5
!
--------------------------------------------
PIAF:
* Running Asterisk Version : Asterisk 1.4.23.1
* Asterisk Source Version : 1.4.23.1
* Zaptel Source Version : 1.4.12.1
* Libpri Source Version : 1.4.9
* Addons Source Version : 1.4.7
pbx*CLI> pri show span 1
------------------------
Primary D-channel: 16
Status: Provisioned, Down, Active
Switchtype: EuroISDN
Type: CPE
Window Length: 0/7
Sentrej: 0
SolicitFbit: 0
Retrans: 0
Busy: 0
Overlap Dial: 0
Logical Channel Mapping: 0
T200 Timer: 1000
T203 Timer: 10000
T305 Timer: 30000
T308 Timer: 4000
T309 Timer: -1
T313 Timer: 4000
N200 Counter: 3
pbx*CLI>
== Primary D-Channel on span 1 up
== Primary D-Channel on span 1 down
pbx*CLI>
debug /var/log/asterisk/full:
-------------------------------
[Jan 28 17:22:03] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:22:05] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1
[Jan 28 17:22:06] VERBOSE[6182] logger.c: == Primary D-Channel on span 1 up
[Jan 28 17:22:06] WARNING[6182] chan_dahdi.c: PRI Error on span 0: We think we're the CPE, but they think they're the CPE too.
[Jan 28 17:22:10] VERBOSE[6182] logger.c: == Primary D-Channel on span 1 down
[Jan 28 17:22:10] WARNING[6182] chan_dahdi.c: No D-channels available! Using Primary channel 16 as D-channel anyway!
[Jan 28 17:22:12] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:22:13] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:22:14] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:22:15] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
/etc/zaptel.conf
-------------------
# Autogenerated by /usr/src/zaptel/kernel/xpp/utils/genzaptelconf -- do not hand edit
# Zaptel Configuration File
#
# This file is parsed by the Zaptel Configurator, ztcfg
#
# It must be in the module loading order
# Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER)
span=1,1,0,ccs,hdb3
# termtype: te
bchan=1-15,17-31
dchan=16
# Span 2: TE2/0/2 "T2XXP (PCI) Card 0 Span 2"
span=2,2,0,ccs,hdb3
# termtype: te
bchan=32-46,48-62
dchan=47
# Global data
loadzone = us
defaultzone = us
zapata.conf
------------
[channels]
language=en
context=default
switchtype=euroisdn
;If you connect to a hicom PBX set your ISDN Numbering Plan Identifier to unknown.
pridialplan=unknown
prilocaldialplan=unknown
signalling=pri_cpe
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
rxgain=0.0
txgain=0.0
group=1
callgroup=1
pickupgroup=1
immediate=no
group = 1
channel => 1-15
channel => 17-31
group = 2
channel => 32-46
channel => 48-62
#include zapata-channels.conf
zapata-channels.conf
-------------------
; Autogenerated by /usr/src/zaptel/kernel/xpp/utils/genzaptelconf -- do not hand edit
; Zaptel Channels Configurations (zapata.conf)
;
; This is not intended to be a complete zapata.conf. Rather, it is intended
; to be #include-d by /etc/zapata.conf that will include the global settings
;
; Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER)
group=0,11
context=from-pstn
switchtype = euroisdn
signalling = pri_cpe
channel => 1-15,17-31
group=
context=default
; Span 2: TE2/0/2 "T2XXP (PCI) Card 0 Span 2"
group=0,12
context=from-pstn
switchtype = euroisdn
signalling = pri_cpe
channel => 32-46,48-62
group=
context=default
I am trying to connect asterisk with a Cisco GW 2600 with E1 pri using a Digium, Inc. Wildcard TE210P dual-span T1/E1/J1 card 3.3V (rev 02),
Errors:
[Jan 28 17:32:33] VERBOSE[6182] logger.c: == Primary D-Channel on span 1 up
[Jan 28 17:32:33] WARNING[6182] chan_dahdi.c: PRI Error on span 0: We think we're the CPE, but they think they're the CPE too.
[Jan 28 17:32:34] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:32:35] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:32:36] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:32:37] VERBOSE[6182] logger.c: == Primary D-Channel on span 1 down
[Jan 28 17:32:37] WARNING[6182] chan_dahdi.c: No D-channels available! Using Primary channel 16 as D-channel anyway!
[Jan 28 17:32:42] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1
[Jan 28 17:32:43] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:32:44] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:32:45] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:32:51] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
please someone help me,
rafael
Configuration details:
Cisco cisco 2650XM (Version 12.2(15)T14)
--------------------------------------------
!
isdn switch-type primary-net5
!
!
voice call send-alert
voice call convert-discpi-to-prog
voice call carrier capacity active
voice rtp send-recv
!
voice service voip
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback none
h323
!
!
controller E1 1/0
framing NO-CRC4
pri-group timeslots 1-31
!
!
!
interface FastEthernet0/0
ip address 192.168.12.210 255.255.255.0
ip route-cache same-interface
no ip route-cache
no ip mroute-cache
load-interval 30
speed 100
full-duplex
!
interface Serial1/0:15
no ip address
no logging event link-status
isdn switch-type primary-net5
isdn incoming-voice data
isdn bchan-number-order ascending
no cdp enable
!
ip http server
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.12.100
!
!
call rsvp-sync
!
voice-port 1/0:15
echo-cancel coverage 32
playout-delay nominal 150
playout-delay minimum low
cptone PE
bearer-cap 3100Hz
!
!
dial-peer voice 10 pots
destination-pattern .T
no digit-strip
direct-inward-dial
port 1/0:15
forward-digits all
!
gateway
timer receive-rtcp 5
!
--------------------------------------------
PIAF:
* Running Asterisk Version : Asterisk 1.4.23.1
* Asterisk Source Version : 1.4.23.1
* Zaptel Source Version : 1.4.12.1
* Libpri Source Version : 1.4.9
* Addons Source Version : 1.4.7
pbx*CLI> pri show span 1
------------------------
Primary D-channel: 16
Status: Provisioned, Down, Active
Switchtype: EuroISDN
Type: CPE
Window Length: 0/7
Sentrej: 0
SolicitFbit: 0
Retrans: 0
Busy: 0
Overlap Dial: 0
Logical Channel Mapping: 0
T200 Timer: 1000
T203 Timer: 10000
T305 Timer: 30000
T308 Timer: 4000
T309 Timer: -1
T313 Timer: 4000
N200 Counter: 3
pbx*CLI>
== Primary D-Channel on span 1 up
== Primary D-Channel on span 1 down
pbx*CLI>
debug /var/log/asterisk/full:
-------------------------------
[Jan 28 17:22:03] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:22:05] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1
[Jan 28 17:22:06] VERBOSE[6182] logger.c: == Primary D-Channel on span 1 up
[Jan 28 17:22:06] WARNING[6182] chan_dahdi.c: PRI Error on span 0: We think we're the CPE, but they think they're the CPE too.
[Jan 28 17:22:10] VERBOSE[6182] logger.c: == Primary D-Channel on span 1 down
[Jan 28 17:22:10] WARNING[6182] chan_dahdi.c: No D-channels available! Using Primary channel 16 as D-channel anyway!
[Jan 28 17:22:12] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:22:13] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:22:14] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
[Jan 28 17:22:15] NOTICE[6182] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
/etc/zaptel.conf
-------------------
# Autogenerated by /usr/src/zaptel/kernel/xpp/utils/genzaptelconf -- do not hand edit
# Zaptel Configuration File
#
# This file is parsed by the Zaptel Configurator, ztcfg
#
# It must be in the module loading order
# Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER)
span=1,1,0,ccs,hdb3
# termtype: te
bchan=1-15,17-31
dchan=16
# Span 2: TE2/0/2 "T2XXP (PCI) Card 0 Span 2"
span=2,2,0,ccs,hdb3
# termtype: te
bchan=32-46,48-62
dchan=47
# Global data
loadzone = us
defaultzone = us
zapata.conf
------------
[channels]
language=en
context=default
switchtype=euroisdn
;If you connect to a hicom PBX set your ISDN Numbering Plan Identifier to unknown.
pridialplan=unknown
prilocaldialplan=unknown
signalling=pri_cpe
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
rxgain=0.0
txgain=0.0
group=1
callgroup=1
pickupgroup=1
immediate=no
group = 1
channel => 1-15
channel => 17-31
group = 2
channel => 32-46
channel => 48-62
#include zapata-channels.conf
zapata-channels.conf
-------------------
; Autogenerated by /usr/src/zaptel/kernel/xpp/utils/genzaptelconf -- do not hand edit
; Zaptel Channels Configurations (zapata.conf)
;
; This is not intended to be a complete zapata.conf. Rather, it is intended
; to be #include-d by /etc/zapata.conf that will include the global settings
;
; Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER)
group=0,11
context=from-pstn
switchtype = euroisdn
signalling = pri_cpe
channel => 1-15,17-31
group=
context=default
; Span 2: TE2/0/2 "T2XXP (PCI) Card 0 Span 2"
group=0,12
context=from-pstn
switchtype = euroisdn
signalling = pri_cpe
channel => 32-46,48-62
group=
context=default
Phone System 